| Application: | Industrial |
|---|---|
| Standard: | GB, ASTM |
| Purity: | >99.5% |
| Alloy: | Alloy |
| Powder: | Not Powder |
| Transport Package: | Wooden |
| Customization: |
|---|
Suppliers with verified business licenses
Audited Supplier GH738 is a nickel-based superalloy reinforced by γ' phase precipitation. It has good gas corrosion resistance, high yield strength and fatigue performance, good process plasticity and stable structure. It is widely used in rotating parts of aero-engine, and the operating temperature is not higher than 815ºC. Cold-rolled and hot-rolled sheet, tube, strip, wire and forgings, castings, fasteners can be produced.
Material introduction
Heat treatment system 1080ºC±10ºC, 4h, air cooling +840ºC, 24h, air cooling +760ºC, 16h, air cooling.
Variety Specifications and Status
It can produce bars, profiles, forging billets, rings, thick plates, thin plates, strips, pipes, wires, sand castings, precision castings and fasteners, etc. Usually delivered without heat treatment, and the plates are delivered after solution treatment. goods.
Melting and casting process
The alloy adopts vacuum induction and vacuum arc remelting process.
Application overview and special requirements
The alloy is widely used in aero-engine gas turbines in China, mainly used for rotating parts such as turbine blades and turbine disks, and has mature experience in use. Due to the high cobalt content of this alloy, it is rarely used in China.
1.1, material grade
GH738
1.2, similar grades
Waspaloy (USA), NC20K14 (France)
1.3. Technical standards of materials
Z9-0106 1986 "Temporary Technical Conditions for GH738 Alloy Bars for Eight Uses of Turbo Shafts"
Q/6S1035-1992 "GH738 alloy bars for high temperature fasteners"
09-1986 "Technical Conditions for Trial Production of GH738 Alloy Flue Gas Disk" (Shanggang No. 5 Plant)
1.4, Chemical composition
Table 1-1
C Cr Ni Co Mo Al Ti
0.03~0.10 18.0~21.0 margin 12.0~15.0 3.5~5.0 1.2~1.6 2.75~3.25
B Zr Fe Mn Si P S Cu
0.003~0.01 0.02~0.08 ≤2.0 ≤0.10 ≤0.15 ≤0.015 ≤0.015 ≤0.1
Note: Trace impurities are ω(Pb)≤0.001%, ω(As)≤0.0025%, ω(Sn)≤0.0012%, ω(Sb)≤0.0025%, ω(Bi)≤0.0001%.
Physical and chemical properties
2.1. Thermal performance
2.1.1. Melting temperature range 1330~1360ºC
2.1.2. Thermal conductivity
Table 2-1
θ/°C 360 460 545 640 770 855 985
λ/(W/(m·C)) 16.8 18.3 20.2 22.4 24.1 25.3 28.0
2.1.3. Specific heat capacity
Table 2-2
θ/°C 360 460 545 640 770 855 985
c/(J/(kg·C)) 515 540 573 603 640 665 707
2.1.4. Linear expansion coefficient
Table 2-3
θ/°C 20~100 20~200 20~300 20~400 20~500 20~600 20~700 20~800 20~900
α/10-6C-1 12.47 12.73 13.04 13.53 13.97 14.47 15.05 15.68 15.95
2.2. Density ρ=8.22g/cm3
2.3. Electrical resistivity
2.4, magnetic energy type
The alloy is non-magnetic.
2.5, chemical properties
2.5.1 Oxidation resistance The oxidation rate of the alloy after 100h in the air medium
Table 2-4
Test time/h 900 1000
Oxidation rate/(g/(m2.h)) 0.083 0.226
2.5.2. Corrosion resistance The alloy has good resistance to salt spray corrosion.
metallographic structure
The structure of the alloy in the standard heat treatment state is composed of γ matrix, Ti(C, N), Nb(C, N), M23C6 carbide and γ'[Ni3(Al, Ti, Nb)] phase, and the γ' content is about 14.5% , is the main strengthening phase of the alloy.
Process performance
1. The forging temperature of the alloy is easy to form between 1220 and 950 °C. The alloy is solution treated after the vigorous forming process.
2. The average grain size of the alloy is closely related to the deformation degree and final forging temperature of the forging.
3. The alloy has good welding performance and can be welded in various ways. Aging treatment after welding can obtain approximately the strength of the fully heat-treated state.
4. The heat treatment of parts is carried out in a neutral or reducing atmosphere without sulfur to avoid vulcanization.
Company Profile
Suppliers with verified business licenses
Audited Supplier 
){kind=link}
){kind=link}